Varmebade

The heating bath HB 1500 is developed for varied tasks. The bath can be filled with water, oil or sand. Modern microprocessors control the temperature. With measuring circuit monitoring for over- and under-temperature, sensor and line short-circuit, as well as sensor and line breakage.

• Microprocessor controller with 4-digits 7-segment display, 10 mm high, green
• Freely configurable
• Self-optimising temperature control
• Measuring and control range up to 260 °C
• Setting of heating power from 1 to 99 %
• Overtemperature switch-off >10 K + setpoint
• Wear-free internal temperature sensor at the bottom of the pot
• On-Off switch 2-pole, green, illuminated
• Switchable to external sensor
• Material bath/housing stainless steel, front and rear anodised aluminium

The heating bath HB 1500-S is developed for varied tasks. The bath can be filled with water, oil or sand. The appliance is equipped with 2 temperature controllers with microprocessor. The upper temperature controller serves as a safety temperature limiter. If the safety temperature is exceeded, the heating is switched off at all poles. The temperature is measured via an internal temperature sensor at the bottom of the pot.

• Microprocessor controller with 4-digit 7-segment display, 10 mm high, green
• Freely configurable
• Self-optimising temperature control
• Measuring and control range up to 260 °C
• Setting of heating power from 2 to 99 %
• Switchable to external sensor
• Material bath/housing stainless steel, front and rear anodised aluminium

Set of rings H 240: To cover the heating bath.
Intermediate base H 159: Allows insertion of vessels into the bath, without affecting the stirrer motion.

The insulated stainless steel baths are suitable for use up to 200°C. All models have a bridge-mounted immersion circulator. With a pump adapter, this combination can also be used with externally closed and externally open (with option level control) applications. Models with the Pilot ONE controller have a variable speed pressure/suction pump and are therefore also suitable for external open applications.

Compact and ergonomic heating safety bath for all tempering media.

• Ergonomic handles
• Key button to lock heating bath temperature
• Clear, black-and-white display
• Permanent set-point/actual temperature display
• 3 different safety operating modes
• USB interface

Compact and ergonomic heating safety bath.

• Ergonomic handles
• Clear, black-and-white display
• Alternating set-point/actual temperature display
• USB interface

For continuous operation. Electrical sand bath with thermostatic temperature control and separate power controller for performance adjustment to the heating requirements. Anodised aluminium alloy hotplate. Excellent uniform temperature distribution over the entire heating surface. The sand bath frame is tightly screwed onto the hotplate so that the sand is in direct contact with the hotplate. Useful depth 50 mm. Stainless steel controller housing, with painted central section. Height-adjustable feet. Connection cable approximately 1.7 m. With earthed plug.

Designed for combination with the IKA ROTAVISC viscometers and covers a wide temperature range.

• A second beaker (600 ml) can be pre-tempered during the measurement
• Optimised water flow management in the insulated bath for fast and precise temperature control.
• Equipped with environmentally friendly natural refrigerant R290
• External pump connection for heating standard vessels according to DIN for absolute viscosity definition with ELVAS spindles or double-walled beakers
• Easy to maintain thanks to easily removable and therefore easy-to-clean air filters

Powerful and high-quality entry-level series for a wide range of applications. Intensive cleaning in dynamic mode or gentle and economic cleaning with quiet operation in eco mode.

• Splash-proof housing and cleaning tank, made of stainless steel
• Electronic selector switch on wipeable membrane keypad.
• LED display of all operating states
• Timer from 1 to 30 min or continuous operation
• Automatic safety switch-off with wake-up function

Made of glass ceramic which offers excellent chemical resistance.

• Fixed safety circuit of 550 °C
• Hot Top indicator: Hot surface warning to prevent burns
• Exact temperature setting via digital display (LED)
• Digital error code display
• Raised control panel for protection against spilt liquids

Made of glass ceramic which offers excellent chemical resistance.

• Fixed safety circuit of 550 °C
• Hot Top indicator: Hot surface warning to prevent burns
• Exact temperature setting via digital display (LED)
• Digital error code display
• Raised control panel for protection against spilt liquids

Annealed quality, 0.1 to 0.5 mm grain size.

This precise digital bath is specifically designed to be used with the Stuart rotary evaporators to give maximum efficiency for the smallest footprint. The clear LED digital display shows the actual bath temperature or the set temperature. Outer case is made from chemically resistant polypropylene.

• Digital temperature display, display resolution 1 °C, temperature control ±1.5 °C (water), ±3 °C (oil)
• Corrosion resistant bowl
• Easy to clean
• Cool touch outer case

For use in histological, clinical and bacteriological laboratories for stretching and drying cut tissue samples.

• With »GFL Technology« for the highest quality, reliability and durability
• With bath body made of black anodized aluminum
• Wide heated bath rim for depositing and drying the samples

For continuous operation. Electrical sand bath with thermostatic temperature control and separate power controller for performance adjustment to the heating requirements. Anodised aluminium alloy hotplate. Excellent uniform temperature distribution over the entire heating surface. The sand bath frame is tightly screwed onto the hotplate so that the sand is in direct contact with the hotplate. Useful depth 50 mm. Stainless steel controller housing, with painted central section. Height-adjustable feet. Connection cable approximately 1.7 m with earthed plug.