Flaskedispensere

• Delivery tubes made of PP
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• For weak acids, alkalis and detergents

For rapid and clean emptying from cans, drums and small barrels up to 60 l.

• Medium-contacting parts made of PP, PE and FKM
• Precise dosing, without dripping
• Pump connection suitable for 64 mm dia. (BSI) container threads
• Stepless length adjustment of immersion tube
• Threaded adapters for most commercially-sold containers available
• Not suitable for HCl

• Delivery tubes made of PVDF
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• For acids, alkalis and chlorine bleaching, not for heavily oxidising acids and alkalis

• Delivery tubes made of PP
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• 1.5 m discharge tube, PVC
• Stopcock made of PP/PE

The manual pressure pump is ideally suited for drawing off, decanting and emptying canisters and barrels. The hand pump is used to create excess pressure that forces the liquid out of the container. The stopcock also allows extraction of small quantities of liquid. The PumpMaster container pump is mounted on the container using a flexible stopper with a variable and adjustable diameter. No special thread adapters are required. PumpMaster fits all commercial container openings with a diameter from 46.5 mm to 60 mm. The immersion tube has a length of 95 cm and it can be shortened depending on the size of the container.

Scope of supply: Drum pump, three bungs in different sizes

When dispensing combustible/explosive liquids pump, both dispensing and filling drum involved in the process must be sufficiently earthed, in order to prevent ignition or explosion through electrostatic discharges. Antistatic set, includes three colour-coded connecting cables with clamps, supplied complete in plastic case.

Transparent with stopcock. Simple to use, suitable for occasional dispensing of non-aggressive liquids from a higher drum to a lower vessel, following the siphoning principle.

• Delivery tubes made of PP
• For small containers, up to 10 l
• Universal bungs made of soft PVC, for container openings of 20 – 36 mm
• For weak acids, alkalis and detergents

Adapter set consisting of:

• 2'' Coarse thread, Mauser, green
• 2'' coarse thread, Tri-Sure^®, brown
• 2'' Fine thread steel drum, blue
• DIN 60, black
• DIN 51, black

Thread adapter set consisting of:

• 3/4'' Hünersdorff
• 3/4" Kautex
• 3/4" cylindrical R 3/4" barrel thread
• 3/4" conical R 3/4" barrel thread
• Hex wrench for threaded adapter

• For ultrapure and aggressive liquids
• Made of solid, pure white PTFE, giving an excellent chemical resistance to all media (with the exception of elemental fluorine)
• With stopcock to prevent the escape of harmful or hazardous liquids and unwanted drips
• Barrel screw joints are availabe as accessories

• For ultrapure and aggressive liquids
• Made of solid, pure white PTFE, giving an excellent chemical resistance to all media (with the exception of elemental fluorine)
• With stopcock to prevent the escape of harmful or hazardous liquids and unwanted drips
• Barrel screw joints are availabe as accessories

The pumps are equipped with two different power supply systems: AccuOne, driven by a high-performance rechargeable battery or EnergyOne, with a power cable for direct connection to mains electricity. Innovative new feature: The power supply units are interchangeable! The rechargeable battery or the power supply unit are fitted with a clip lock and are removable. They can be exchanged quickly and easily. Thus AccuOne can also be operated with the power supply cable unit and EnergyOne can be operated with the rechargeable battery. The drive can also be disconnected quickly and easily from the pump station with a clip lock. This makes it possible to use one drive for filling at several stationary pump stations. AccuOne and EnergyOne are designed for applications in which even very small amounts of liquid can be added to small containers with narrow openings. The TouchPanel is sealed against dust, dirt and water. By a foil Keyboard it can be used to regulate the flow rate continuously and precisely from 0.4l/min to 12 l/min. The light and powerful pumps are made of high-quality materials, PP, PTFE and Hastelloy C, to ensure outstanding chemical resistance. Please make note of detailed information related to chemical resistance!

• For decanting acids, caustic solutions and aggressive detergents
• Excellent recovery of residual liquid in the barrel provided by base-sitting, non-return valve and steplessly adjustable immersion tube
• For barrels and tanks from 30 to 1000l.

• For decanting acids, caustic solutions and aggressive detergents
• Excellent recovery of residual liquid in the barrel provided by base-sitting, non-return valve and steplessly adjustable immersion tube
• For barrels and tanks from 30 to 1000 l

Stainless steel V2A and PTFE.
For safe dispensing of liquids with a low flash point . Electrostatic charge can be dissipated through accessories antistatic set and drum screwthread connection. Not suitable for acetone.

Stainless steel V2A and PTFE.
For safe dispensing of liquids with a low flash point . Electrostatic charge can be dissipated through accessories antistatic set and drum screwthread connection. Not suitable for acetone.

Nickel-plated brass. G 2" steel fine outer thread.

Lightweight and powerful pump for transferring small amounts of aqueous liquids up to 300 mPas from cans and drums with infinitely variable speed controller.

• Motor 230 V, 200 W (IP 24)
• Seal less pump tube
• Suitable accessory flow meter required
• Pump with tubing connection

• Polypropylene version for acids and alkalis
• Stainless steel version for low-viscosity lubricants

For safe handling of environmentally hazardous and aggressive liquids as well as inflammable and explosive fluids.

Drum pumps supplied with: 230V motor, 5m cable and plug, pump tube and tubing connection. Explosion-proof version additionally supplied with earthing strap.

Pump set "alkalis"
For low-viscosity alkali solutions such as sodium chloride, Potassium hydrate, ammonia, formic acid and acetic acid.
Supplied with: Pump, 2.0m PVC tubing (DN19 fitting), PP nozzle and barrel adapter

Pump set "acids"
For low-viscosity acids such as hydrochloric, phosphoric, chromic, citric acids and battery acid.
Supplied with: Pump, 2.0m PVC tubing (DN19 fitting), PP nozzle and barrel adapter

Pump set "mineral oils"
For low-viscosity mineral oil products such as Diesel, fuel, hydraulic, machinery and motor oils.
Supplied with: Pump, 2.0m PVC tubing (DN25 fitting), aluminium nozzle and PP barrel adapter

Pump set "solvents"
For easily flammable hydrocarbons such as ethanol, gasoline, butanol, isopropanol, kerosene, methanol and petroleum.
Supplied with: Pump, 2.0m solvent-resistant tubing (DN19 fitting), brass conductive tubing coupling and nozzle, earthing strap and PP barrel adapter

• Delivery tubes made of PP
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• For weak acids, alkalis and detergents

• Delivery tubes made of PP
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• 1.5 m discharge tube, PVC
• Stopcock made of PP/PE (Ø 10 mm)

• Delivery tubes made of PVDF
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• For acids, alkalis and chlorine bleaching, not for heavily oxidising acids and alkalis

• Delivery tubes made of stainless steel
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• For liquids that are not easily flammable in Hazard Category AIII (VbF)

With flexible discharge tubing for drawing off into larger canisters and containers. Convenient liquid transfer as the canister can be left standing on the floor. The connection cone is pressed against the canister manually.
The pump is fitted with a gas-displacement device for odour-free, liquid transfer. The pump can be hermetically sealed with 2 ball valves.

• Parts in contact with media: Stainless steel AISI 304 (1.4301), PTFE
• With gas-tight barrel screw joint, 2" fine thread

• Delivery tubes made of stainless steel
• Universal bungs made of soft PVC, for container openings of 30 – 70 mm
• For liquids that are not easily flammable in Hazard Category AIII (VbF)

These new magnetic drive pumps are designed for pumping acids, bases, mixtures of acids and bases, solvents, photochemicals into alkali stripping baths, galvanic baths, as well as radioactive, sterile, expensive or highly corrosive liquids. The pumps are sealless. The impeller is driven by the magnetic force of the outer magnets, therefore no mechanical seal is required. As the pump housing is hermetically sealed no leaks can occur. The use of high performance,
permanent magnets, ensures high transmission forces even at elevated temperatures.

• viscosity up to 20 mPas
• pump complete with flanged-to motor

The self-closing discharge (with auto-stop function) of the Mini solvent pump ensures absolutely precise filling with no dripping at all. Dosing is even easy in very small containers such as test tubes, which present no problems. A hose can optionally be fastened onto the discharge spout (internal Ø 6 mm), thus making it possible to fill the container from a greater distance.

The Mini solvent pump is especially compact and very well balanced, which makes it possible to fill without tipping, even from very small containers.

Thanks to its sturdy design and high-quality materials, the Mini solvent pump consistently ensures neat and reliable filling throughout its long service life, easily and conveniently.

• Ideal for 1-5 l containers
• Connecting thread GL 45
• Parts in contact with medium made of PTFE and stainless steel (1.4301, 1.4404)
• PTFE hose (6 x 8 mm) 0.4 m
• Including grounding cable 2 m
• Adapters available as accessories for S 40, GL 38 and GL 32

For filling off high purity liquids such as solvents. Due to the barrel screw joint and the stopcock, the container and the pump can be hermetically sealed. Electrostatic charge can be dissipated through the accessory antistatic set (please order seperately).

• Medium-contacting parts made opf stainless steel (1.4301) and PTFE
• For barrels up to 220 litres, immersion tube can be steplessly adjusted to the barrel depth
• Suitable for steel barrels with R 2'' thread

For filling off high purity liquids such as solvents. Due to the barrel screw joint and the stopcock, the container and the pump can be hermetically sealed. Electrostatic charge can be dissipated through the accessory antistatic set (please order seperately).

• Medium-contacting parts made of stainless steel (1.4301) and PTFE
• For barrels up to 220 litres, immersion tube can be steplessly adjusted to the barrel depth
• Suitable for steel barrels with R 2'' thread

For contamination-free removal of organic solvents and flavouring agents. Can be completely closed off with two ball valves so that no dangerous vapours can escape after dispensing. Electrostatic charge can be dissipated through the accessory antistatic set (please order separately).

• Medium-contacting parts are made of stainless steel (1.4301) and PTFE
• For containers up to 60 litres
• Suitable for containers with R 2'' thread

For contamination-free removal of organic solvents and flavouring agents. Can be completely closed off with two ball valves so that no dangerous vapours can escape after dispensing. Electrostatic charge can be dissipated through the accessory antistatic set (please order separately).

• Medium-contacting parts are made of stainless steel (1.4301) and PTFE
• For containers up to 60 litres
• Incl. connector thread for pull-out spouts with Ø 35 mm

For Bürkle pumps and discharge stopcocks.

• With delivery tubes made of PP/PVC
• For safe filling of car batteries with acid or distilled water
• With tube shutoff valve
• With dosing tip for precise filling

The gas-tight barrel pump reduces the escape of dangerous, health-endangering or malodorous gases when filling liquids. The resulting vapours are returned directly to the original container via the gas pendulum line.

• Medium-contacting parts, PP, PE and PVC (hose)
• Steplessly extendable telescopic tube for barrel depths of 40 - 67 cm
• Universal adapter for container openings of 34 - 70 mm

For StopCock spigots and ball valves.

For ball valves.

For sampling cohesive, caked and not free-flowing substances.

• Food-safe
• Autoclavable

• Self-venting
• NW 13 mm
• 3/4" thread connection outside
• Seal made of natural rubber