Adapters, Clips, Clamps

Assemblies and Tubings
Hamilton Luer Lock tubing assemblies are ideal for quickly connecting and disconnecting components with male luer locks suitable for micro fluidic applications. Hamilton offers a wide varitey of chemically inert tubing assemblies for specific fluid applications. Different gauges, lengths, hub assemblies, and fittings are available according to standard or customer specification. To build your own assemblies, Hamilton offers fitting kits and tubings. Hamilton fittings and adapters are installed finger tight and provide leak tight seal rated to 0.6 MPa.

Hub Tubing Assemblies with 2 Hubs and further tubing lengths available on request.
The tubing is 300 mm in length but can be trimmed shorter to a desired length.

Flanged PTFE tubing with black tube end fittings UNF ¼" 28 G made of PP and washers made of PA. The tubing is ready for use. Temperature resistant from 0 to +100 °C, pressure resistant up to 30 bar, universal chemical resistance.

Fingertight fittings for HPLC tubing made of PEEK.

For 250 µl RN needle syringes and larger. Port diameter 1.5 mm, Inert Gas Sampling Valve 1 mm.

Clamp is molded of strong, durable plastic with serrated jaws. For closing thin-walled tubes.

• Autoclavable
• One hand open and close operation
• For tubes up to 0.82mm wall thickness
• Secure closure by serrated jaws over a length of 27 mm
• Attach at any point on tubing without disconnecting tubing

Brass nickel plated. Bottom hinged.

Nickel plated. Spring pinchclip.

PP. Autoclavable.

Elbow taper thread connectors.

T-taper thread connectors.

T-shape.

Taper thread connectors, straight.

To connect tubes.

• Food safe
• Autoclavable

• Temperature resistant up to 160 °C max.
• Highly resistant to chemicals

Y-shape.

For screw caps with bore.

The bottle caps with quick disconnect coupling or FitQuik^® tubing connection integrated in a cap for all common laboratory bottles with GL 45 thread, blue. The BQ45GL series has a hydrophobic packaging vent, a polyethylene gasket and hose barb with 1/1"" (6.35 mm) ID for mounting a dip tube.

• For all bottles with thread GL 45
• Factory-installed quick couplings
• Tight closure even without seal
• One hand operation

Acetal resin.
Straight.

For StopCock spigots and ball valves.

For conversion of all SI Analytics pH-meters with BNC entrance into DIN or vice versa.

DIN S-1: DIN adapter set.
O DIN S-1: The open DIN spindle set measures viscosities according to DIN 53019 and can be used with customer-specific vessels. The set includes a single-wall-open-jacket to quickly dive into the sample liquid as well as a coaxial cylinder system for the analysis of the sample at a specific shear rate and shear stress is included.
ELVAS-1: The extremely low viscosity adapter spindle set ELVAS-1 includes a double jacket to quickly heat up or cool down the sample as well as a coaxial cylinder system for the analysis of the sample at a specific shear rate and shear stress. This 16 ml spindle is commonly used with the ROTAVISC lo-vi and allows measurements from 1 mPas (water temperature at 20 °C). The spindle without the water jacket can also be used in customer-specific vessels.
VAN-1: The vane spindle set allows the viscosity measurement of suspensions. Four vane spindles are included in the delivery.
T-SP-Set: Set with 6 T spindles
SAS-1: Spiral adapter to measure the viscosity of very sticky and other viscous samples. Additionally, it is possible to analyse the fluid behavior of different shear rates.
SP set-1: Standard spindle set, inculdes 4 spindles (SP1, SP2, SP3, SP4).
SP set-2: Standard spindle set, inculdes 6 spindles (SP7, SP8, SP9, SP10, SP 11, SP12)

With embossed directional arrow or printed in black.

• Conical spouts
• Resistant to compression max. 4 bar
• Operating temperature 0 to 40 °C
• With PP valve ball, on request also with ball made of stainless steel or PTFE