Autoclaves

Service kit 1: with lid gasket, valve gasket, gasket for exhaust cock and manometer, steam valve
Service kit 2: with lid gasket, control valve gasket, seals for exhaust cock and pressure gauge, steam valve and safety valve
Service kit 3: with door gasket, safety valve and bacteria filter

Zur biologischen Kontrolle gehört der Einsatz von Indikatoren, welche überprüfen sollen, ob in jeder Ladung alle Mikroorganismen abgetötet wurden. Die Bio-Indikatoren sind einzigartig, da sie direkt anzeigen, wie viele mikrobielle Sporen im Sterilisator tatsächlich abgetötet wurden. Dank der Zuverlässigkeit und Qualität der erhaltenen Informationen, kann der regelmässige Einsatz eines Bio-Indikators zu einer verbesserten Leistungsfähigkeit des Sterilisationsprozesses und somit zu besseren Ergebnissen.

Eigenschaften:

• Zur selbständigen Auswertung
• Leichte Handhabung
• Sinnvoll nach Reparaturen/Wartungen von Autoklaven

Anwendung:

• Programm 3.5 Minuten, Haltezeit bei 121 °C oder 134 °C
• Nach der Sterilisation die Ampulle "aufbrechen", um die Nährlösung mit dem Sporenstreifen in Kontakt zu bringen
• Ergebnisse in 48 Stunden
• Erfüllt die Norm EN ISO 11138

Its versatility and compact construction make autoclaves especially interesting for small labs or they can be used as an optimal addition to a large autoclave.

All models: Low-maintenance. No water connection required. Compliant with 2014/35/EU Low Voltage Directive, 2014/30/EU EMV Directive, 2011/65/EU Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Vertical models: Class N steam sterilisers. Venting procedure: free steam flow process or fractional flow procedure. A heater is integrated in the bottom of the chamber, but it is not exposed. Therefore, it cannot calcify. The autoclaves are easy to transport and location independent. All you need is a power supply and a mixture of tap water and demineralised water. Safeguarded by a multiple safety system. In aluminum models, it consists of an overpressure valve, a pressure valve, a safety lock inside the lid to prevent opening under pressure and the overpressure safety cavity. In stainless steel models, it consists of an overpressure valve, a pressure valve, a safety lock inside the lid to prevent opening under pressure and a two-bimetal safeguard to prevent overheating of the device.
The fully automated, vertical laboratory autoclave is suitable for extended/ long- term cycles, material tests, HAST Test, pressure vessel test, ICP - TM 650, food preservation, culture media preparation, sterilisation of waste, unpackaged solids without hollow bodies, liquids, bottles, instruments, synthetic materials and rubber. It is operated via of a 7-inch high-resolution tablet. All operating steps are explained with videos directly on the tablet. Compliance with GLP requirements through automatic documentation of users and cycles. Process protocols are stored in the CertoCloud for 10 years. Integration into laboratory data systems possible. For autoclaving liquids, a PT100-media sensor is optionally available.

Scope of suppy: Autoclave, stable instrument panel with 3 feeds, minimum water level indicator, power cable, tablet

Specifications
Chamber diameter:	260 mm
Chamber depth:	350 mm
Air evacuation:	Fractional flow procedure
Chamber material:	Stainless steel 316L
Operating pressure:	2.7 bar
Heating capacity:	1300 W
Power supply:	230 V ±10 % / 50 - 60 Hz

Accessories Accessories for Autoclaves, CertoClav Alternative Tabletop autoclaves CertoClav MultiControl

Accessories Digital vertical autoclaves, AES series

HMT 230/260 FA - for standard tasks:

• Certified according to regulation 93/42/EEC
• Available in 2 sizes with a volume of 16 or 24 liters
• 9 sterilization programs, fully automatic: 121 °C wrapped / unwrapped solid items; with or without drying, 135 °C wrapped / unwrapped solid items; with or without drying, Liquid program: 121 °C, 40 min.
• Controlled by a microprocessor
• Simple digital display
• Water tank
• Electromechanical overheating protection
• Safety valve
• Mechanical pressure-dependent door lock
• Reset/emergency button
• Easy maintenance

HMT 230/260/300 MA - versatile table-top autoclave:

• Certified according to regulation 93/42/EEC
• Available in 3 sizes with a volume of 16, 24 or 40 liters
• Powerful integrated vacuum pump, an essential feature for sterilizing tubes and hollow components
• 7 sterilization programs, fully automatic: 121 °C wrapped / unwrapped (vacuum), 134 °C wrapped / unwrapped (vacuum), Liquid and prion programs, Bowie-Dick test
• Controlled by a microprocessor
• Progress indicator
• Internal water tank
• Electromechanical overheating protection
• Electronic overpressure protection
• Pressure safety valve
• Mechanical pressure-dependent door lock
• Reset/emergency button
• Easy maintenance

HMT 260/300 MB - premium table-top autoclave:

• Certified according to regulation 93/42/EEC
• Available in 2 sizes with a volume of 24 or 40 liters
• Powerful integrated vacuum pump, an essential feature for sterilizing tubes and hollow components
• 5 sterilization programs, fully automatic: Sterilization of wrapped items: 121 °C - 30 min.; 134 °C - 15 min., Sterilization of unwrapped items: 121 °C - 15 min.; 134 °C - 4 min., Individual temperature selection from 105° to 135 °C, Preset prion program
• 3 test programs: leakage test, helix test, Bowie-Dick test
• Controlled by a microprocessor
• Easy operation with a LCD display
• Documentation / data storage via SD card and printer
• Drying program, 1- 60 minutes
• 4 literwater tank, to be filled manually or automatically (purified water)
• Various safety features, e.g. safety valve or pressure-dependent door lock
• With modern design, easy maintenance

Accessories

Due to the intelligent combination of vacuum, pressure and steam, the autoclaves are suitable for liquids and solids of all kinds. The additional media sensor guarantees a complete sterilisation of liquids such as culture media. Solids of all kinds and hollow materials are optimally sterilised with the help of a vacuum pump. The preheatable chamber, cooling-ventilation and vacuum pump guarantees short cycle times from 20 minutes including drying time.

• 7-inch touchscreen
• Including free CertoCloud software for all protocols and programs
• Remote maintenance, alarm system via PC, tablet or smartphone
• Notification by e-mail and SMS
• 12 customisable programs (45 l version with 8 customisable programs)
• Interfaces: USB, WiFi, Ethernet, Bluetooth, SD-Card
• Integrated documentation (GMP/GLP conform)
• Standard interfaces for bar scanner, protocol and label printer

Scope of suppy: Autoclave, tray set, power cable, touchscreen

Specifications
Temperaturrange:	105 ... 134 °C
Cooling system:	Air venting
Chamber material:	Stainless steel 304L
Operating pressure:	2.3 bar
Heater power:	2400 W
Power supply:	220 V ±10 % / 50 - 60 Hz

Its versatility and compact construction make autoclaves especially interesting for small labs or they can be used as an optimal addition to a large autoclave.

All models: Low-maintenance. No water connection required. Compliant with 2014/35/EU Low Voltage Directive, 2014/30/EU EMV Directive, 2011/65/EU Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Vertical models: Class N steam sterilisers. Venting procedure: free steam flow process or fractional flow procedure. A heater is integrated in the bottom of the chamber, but it is not exposed. Therefore, it cannot calcify. The autoclaves are easy to transport and location independent. All you need is a power supply and a mixture of tap water and demineralised water. Safeguarded by a multiple safety system. In aluminum models, it consists of an overpressure valve, a pressure valve, a safety lock inside the lid to prevent opening under pressure and the overpressure safety cavity. In stainless steel models, it consists of an overpressure valve, a pressure valve, a safety lock inside the lid to prevent opening under pressure and a two-bimetal safeguard to prevent overheating of the device.
The vertical laboratory autoclave with valve control is suitable for sterilisation of unpackaged solids without hollow bodies, liquids, bottles, instruments, synthetic materials, food preservation, culture media preparation and waste. A precision manometer with drag pointer and a precision thermometer ensure that operations and processes are precise. This autoclave is available in two versions, each with two temperature levels. Pressure control via valve, temperature control via thermostat. Pressure valves are not interchangeable, because the thermostat of the device is perfectly adapted and calibrated to the valve.

Scope of supply: Autoclave, stable instrument panel with 3 feeds, minimum water level indicator, power cable

Specifications	EL 12 // EL 18
Chamber diameter:	240 mm
Chamber depth:	260 // 390 mm
Air evacuation:	Free steam flow process
Chamber material:	Aluminium
Operating pressure:	2.7 bar
Heating capacity:	1900 W
Power supply:	230 V ±10 % / 50 - 60 Hz

Accessories Accessories for Autoclaves, CertoClav Alternative Tabletop autoclaves CertoClav MultiControl

Small, robust and cost effective with its stainless steel casing. The Minichiller is the smallest Unichiller in the world. Minichillers are available with air or water-cooled refrigeration systems, illuminated level indicator, overflow and drain on the front. The filling port is on the top of the unit. All models use natural refrigerants as standard. Minichillers have suction and pressure pumps and therefore have the advantage of have a high flow at low pressure. This is particularly interesting for all pressure sensitive applications (e.g. glass condensors).

Supply req.:

230 V 50/60 Hz

This autoclave is microprocessor controlled and monitored with 10 sterilisation programmes of which 4 are fixed and 6 are freely selectable and has bacteriological filters included by default.

• Operating temperature range 100 °C to 134 °C
• On request, also available with B Class
• RS 232 interface
• Fully automatic functions
• With water reservoir, pre-vacuum and drying
• Case and lid shrouding are AISI 304 stainless steel
• Sterilisation chamber, lid and sealing system are AISI 316 stainless steel
• Electrical heating with protected heating elements
• Safety pressure valve
• Safety thermostat
• Automatic steam controlled by Touch Screen microprocessor
• Manual valves for emptying the sterilisation chamber and for draining steam
• Equipped with mesh stand on the chamber base and trays
• Supply requirements: 230 V 16 A single phase

These autoclaves are microprocessor controlled and monitored with 10 sterilisation programmes of which 4 are fixed and 6 are freely programmable.

• Operating temperature range 100 °C to 134 °C
• On request also available with with vacuum pump and steam generator
• Agar modus (40 °C to 80 °C)
• RS 232 interface
• Timer
• Programmable auto-start (24 h)
• Fully automatic functions
• Case and lid shrouding are AISI 304 stainless steel
• Sterilisation chamber, lid and sealing system are AISI 316 stainless steel
• Electrical heating with protected heating elements in the interior of the chamber
• Safety pressure valve
• Safety thermostat
• Automatic steam controlled by microprocessor
• Manual valves for emptying the sterilisation chamber and for draining steam
• Supply requirements:

AES-12 and AES-75: 230 V 16 A single phase
AES-110 and AES-150: 400 V + Neutral (3-phase)

Accessories Accessory baskets for Digital vertical autoclaves, AES series

Its versatility and compact construction make autoclaves especially interesting for small labs or they can be used as an optimal addition to a large autoclave.

All models: Low-maintenance. No water connection required. Compliant with 2014/35/EU Low Voltage Directive, 2014/30/EU EMV Directive, 2011/65/EU Directive on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

Vertical models: Class N steam sterilisers. Venting procedure: free steam flow process or fractional flow procedure. A heater is integrated in the bottom of the chamber, but it is not exposed. Therefore, it cannot calcify. The autoclaves are easy to transport and location independent. All you need is a power supply and a mixture of tap water and demineralised water. Safeguarded by a multiple safety system. In aluminum models, it consists of an overpressure valve, a pressure valve, a safety lock inside the lid to prevent opening under pressure and the overpressure safety cavity. In stainless steel models, it consists of an overpressure valve, a pressure valve, a safety lock inside the lid to prevent opening under pressure and a two-bimetal safeguard to prevent overheating of the device.
The PT100 sensor-controlled, vertical laboratory autoclave is suitable for extended/ long- term cycles, material tests, HAST test, pressure vessel test und ICP - TM 650, food preservation, culture media preparation, sterilisation of waste, unpackaged solids without hollow bodies, liquids, bottles, instruments, synthetic materials and rubber. Basic version of PC software for data monitoring is included. With this software, you can only set single-step programs. For multi-step programs, PC software professional version is required.

The CertoClav MultiControl 2 Touch is additionally equipped with a 7-inch robust high-resolution tablet. The operating steps are explained with videos on the screen.

• Programmable from 1 minute to 30 days and from room temperature to 140 °C
• Automated process control and error detection
• USB port
• Printer port (RS232) for printing sterilisation protocols

Scope of suppy:
MultiControl 2: Autoclave, stable instrument panel with 3 feeds and minimum water level indicator, power cable, MC2 controller
MultiControl 2 touch: Autoclave, stable instrument panel with 3 feeds and minimum water level indicator, power cable, MC2 controller, tablet

Specifications
Chamber diameter:	260 mm
Chamber depth:	350 mm
Air evacuation:	Fractional flow procedure
Chamber material:	Stainless steel 316L
Operating pressure:	2.7 bar
Heating capacity:	1300 W
Power supply:	230 V ±10 % / 50 - 60 Hz

Accessories Accessories for Autoclaves, CertoClav Alternative Tabletop autoclaves CertoClav MultiControl

The compact and space saving table top units of the Laboklav 25 series provides you most applications of bigger table top units:

• sterilisation of liquids in open and lightly closed vessels, also with air re-cooling system
• sterilisation of instruments, also with pre-vacuum and drying vacuum
• waste sterilisation at 134 °C
• optional exhaust air filtration system
• volume of chamber: 25 l
• max. permissible pressure: 2.8 bar
• sterilising temperature: 98 to 138 °C

A unique design meets innovative technical solutions:

• optimal use of chamber volume - sufficient for 5 x 1 l standard bottle incl. cap
• lid made of temperature resistant safety glass and lid cover made of safety glass
• LED front lightning to visualise cycle progress
• motor driven and self-checking closing mechanism
• flexible temperature reference sensor PT100 as serial function
• Thermolocking device according to IEC 61010-2-40

Chamber volume/Chamber size	25L useable , Ø 265mm x 465mm Chamber illumination by white LED light
Load:	e.g. 5 x 1L bottle up to 5kg instruments
Dimensions (W x D x H): Space requirement on the table: Weight:	440mm x 540mm x 660mm 440mm x 550mm + 110 for door overhang approx. 65kg
Max permissible pressure (PS): Max. permissible temperature (TS):	2.8 bar 138°C
Chamber material:	Stainless steel, chamber lid made from temperature proof safety glass
Housing:	Powder coated, red; Front cover from transparent safety glass; Process illumination (LED) in Blue, Red and Green
Steam generation:	Integrated steam generator with dry heating elements
Heating power: Electrical connection:	2kW 230V ~ 50 Hz, 16A
Lid closing system:	Motorized closing system
Sterilisation temperature: Feed water supply:	98 to 135 °C, adjustable Integrated feed water tank with manual filling
Exhaust steam condensing:	Included, discharge into integrated condensate tank
Thermo locking acc. to IEC 61010-2-43 (TRB 402):	Integrated with flexible reference temperature sensor opening, temperature adjustable
Control:	Micro processor with LCD Display; Code protected access to programming levels; Serial interface RS 485; Internal storage chip to store cycle data of approx. 150 cycles, visualisation and print out at a later stage is possible
Programms:	Up to 10 programms, depending on the integrated option, all programmes can be individualized
Norms and regulations:	Manufactured in Germany in full compliance with the relevant norms and regulations. Serial approval by German TUV, CE marking according Pressure Device Directive (Commissioned by factory service at an additional cost)

Accessories Accessories for Steam steriliser Laboklav 25

• Certified according to the Pressure Equipment Directive 2014/68/EU
• Available in 2 sizes with 50 and 80 liters of effective usable volume
• Innovative locking system with motorized lid including pressure and temperature monitoring
• Steam generation in the chamber
• High energy efficiency and long service life
• Rapid cooling for short cooling times
• Also available with flexible temperature sensor for the sterilization of liquids
• Timer function and 4 program groups with 3 sub-groups each, including night and dissolution program, adjustments for customized programs are always possible
• No water/waste-water installation required
• Castors for mobile use
• Easy to clean plastic surface with rounded edges in contact areas (no burns or injuries).
• Electrical, mechanical and constructional factors guarantee the highest level of quality and user protection
• The accessories make it possible to configurate the autoclave according to your wishes
• Exhaust air filters for laboratories of safety level S2 and higher are also available

Specifications
Automatic start:	1 minute to 7 days, Night programme
Time of sterilization:	1 to 300mins.
Power supply:	220-240V a.c.
Sealing:	at the push of a button, fully automatic
Boiler material:	SUS304 (rust resistant, stainless steel)

Accessories Accessories for HG series steam sterilisers

Tireless, durable and ingeniously simple

• Certified according to the Pressure Equipment Directive 2014/68/EU
• Available in 4 sizes with 25, 50, 85 and 110 liters of effective usable volume
• Simple, reliable and with a long service life, your perfect choice for standard tasks
• Optionally available with flexible temperature sensor for the sterilization of liquids
• For all devices up to 110 liters only a single-phase power supply (220/240 V; 50/60 Hz) is required
• Timer function and 3 program groups with a max. of 6 programs including dissolution program, adaptions for customized programs are always possible
• No installation to a feed water supply required
• Castors for mobile use
• Easy to clean plastic surface with rounded edges in contact areas (no burns or injuries)
• Electrical, mechanical and constructional factors guarantee the highest level of quality and user protection
• The accessories make it possible to configurate the autoclave according to your wishes
• Exhaust air filters for laboratories of safety level S2 and higher are optionally available

Accessories Accessories for HV series steam sterilisers

Laboklav 80 series provides an extensive and diversified range of equipment variants - customized for you laboratory application. The focus is on safe and reproducible processes, safety for the user and the environment as well as a comfortable operation of the autoclave. All steam steriliser are:

• suitable for the liquid sterilisation in open and lightly closed vessels, solid sterilisation and waste sterilisation at 134°C
• upgradable for high demanding laboratory applications
• volume of chamber: 80l
• max. permissible pressure: 2.8bar
• sterilising temperature: 98°C to 138°C
• motor driven and self-checking closing mechanism
• flexible temperature reference sensor PT100 as serial function
• Thermolocking device according to IEC 61010-2-40

A unique installation concept for varied installation possibilities:

• The autoclave can be installed as vertical or as horizontal unit - without additional costs!
• The lid can optionally be opened to the right, to the left or backwards.
• All units can be delivered in three colours: red, green or blue.

Numerous equipment variants:

• vacuum system for difficult to de-aerate solids incl. fractionated pre-vacuum and drying vacuum
• fast re-cooling system for liquid sterilisation using a double jacket, without rejection of demineralised water
• upgrade of the re-cooling system with counter pressure and fan possible - for further reduction of batch times
• optional exhaust air filtration system

Aufgrund ihrer kompakten Größe sind die Tischautoklaven besonders für kleine Labore oder als ideale flexible Ergänzung neben einem großen Autoklaven interessant.

Alle Modelle: Wartungsarm. Kein Wasseranschluss notwendig. Alle Geräte entsprechen den folgenden Normen und Vorschriften: 2014/35/EU Niederspannungsrichtlinie, 2014/30/EU EMV Richtlinie, 2011/65/EU Richtlinie zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten.

Vertikale Modelle: Gehören zu den Dampfsterilisatoren der Klasse N, die Entlüftung erfolgt durch Strömungsverfahren oder fraktioniertes Entlüften. In den Boden der Kammer ist eine Heizung eingepresst, dabei liegen die Heizelemente jedoch nicht direkt im Wasser und können so nicht verkalken. Sie sind transportabel und standortunabhängig. Es wird lediglich eine Stromversorgung benötigt. Die Wasserversorgung erfolgt mit einem Gemisch von Leitungswasser und demineralisiertem Wasser. Gesichert sind Autoklaven durch ein Mehrfach-Sicherheitssystem. Bei den Aluminium-Modellen besteht dieses aus einem Überdruckventil, einem Druckventil, einer Sicherheitsdeckelverriegelung gegen Öffnen unter Druck und der Überdrucksicherheitsausnehmung. Bei den Edelstahl-Modellen besteht dieses aus einem Überdruckventil, einem Druckventil, einer Sicherheitsdeckelverriegelung gegen Öffnen unter Druck und einer Zwei-BI-Metallsicherungen gegen Überhitzung des Gerätes.
Der CertoClav Classic ist die Weiterentwicklung des EL aus korrosionsbeständigem, elektropolierten Edelstahl. Er ist für die Sterilisation von unverpackten Feststoffen ohne Hohlkörper, Flüssigkeiten, Flaschen, Instrumenten, Kunststoffen, Lebensmittelkonservierung, Nährmedienaufbereitung und Müllsterilisation geeignet. Mit integrierter Zeitschaltuhr.

Lieferumfang: Autoklav, stabile Instrumentenplatte mit Standfüßen, Minimum-Wasserstandsanzeiger, Netzkabel

Spezifikationen
Kammerdurchmesser:	260 mm
Kammertiefe:	350 mm
Entlüftung:	Strömungsverfahren
Kammermaterial:	Edelstahl
max. Betriebsdruck:	2,7 bar
Heizleistung:	1300 W
Netzanschluss:	230 V ±10 % / 50 - 60 Hz

Accessories Zubehör für Autoklaven, CertoClav Alternative Tischautoklaven CertoClav MultiControl

Aufgrund ihrer kompakten Größe sind die Tischautoklaven besonders für kleine Labore oder als ideale flexible Ergänzung neben einem großen Autoklaven interessant.

Alle Modelle: Wartungsarm. Kein Wasseranschluss notwendig. Alle Geräte entsprechen den folgenden Normen und Vorschriften: 2014/35/EU Niederspannungsrichtlinie, 2014/30/EU EMV Richtlinie, 2011/65/EU Richtlinie zur Beschränkung der Verwendung bestimmter gefährlicher Stoffe in Elektro- und Elektronikgeräten.

Vertikale Modelle: Gehören zu den Dampfsterilisatoren der Klasse N, die Entlüftung erfolgt durch Strömungsverfahren oder fraktioniertes Entlüften. In den Boden der Kammer ist eine Heizung eingepresst, dabei liegen die Heizelemente jedoch nicht direkt im Wasser und können so nicht verkalken. Sie sind transportabel und standortunabhängig. Es wird lediglich eine Stromversorgung benötigt. Die Wasserversorgung erfolgt mit einem Gemisch von Leitungswasser und demineralisiertem Wasser. Gesichert sind Autoklaven durch ein Mehrfach-Sicherheitssystem. Bei den Aluminium-Modellen besteht dieses aus einem Überdruckventil, einem Druckventil, einer Sicherheitsdeckelverriegelung gegen Öffnen unter Druck und der Überdrucksicherheitsausnehmung. Bei den Edelstahl-Modellen besteht dieses aus einem Überdruckventil, einem Druckventil, einer Sicherheitsdeckelverriegelung gegen Öffnen unter Druck und einer Zwei-BI-Metallsicherungen gegen Überhitzung des Gerätes.
Der PT100-Sensor gesteuerte, vertikale Laborautoklav ist für Langzeitzyklen, Materialtests, HAST Test, Pressure Vessel Test, ICP - TM 650, Lebensmittelkonservierung, Nährmedienaufbereitung, Sterilisation von Abfällen, unverpackten Feststoffen ohne Hohlkörper, Flüssigkeiten, Flaschen, Instrumenten, Kunststoffen und Gummi geeignet. Eine Software zur Aufzeichnung der Prozessdaten via USB ist als Basislizenz inkludiert. Ohne Anschluss eines PC können nur Programme eingestellt werden, die lediglich einen Zeit- und Temperaturschritt umfassen. Für Programme, die mehrere Zeit- und Temperaturschritte umfassen, wird die PC-Software Professional Version benötigt.

• Programmierbar von 1 Minute bis 30 Tage und von Zimmertemperatur bis 140 °C
• Automatische Prozesssteuerung und Fehlererkennung
• USB-Anschluss
• Druckeranschluss (RS232) zur Ausgabe von Sterilisationsprotokollen

Lieferumfang: Autoklav, stabile Instrumentenplatte mit Standfüßen und Minimum-Wasserstandsanzeiger, Netzkabel, MC2 Steuerungseinheit

Spezifikationen
Kammerdurchmesser:	240 mm
Kammertiefe:	260 mm
Entlüften:	fraktioniertes Entlüftungsverfahren
Kammermaterial:	Aluminium
Betriebsdruck:	2,7 bar
Heizleistung:	1900 W
Netzanschluss:	230 V ±10 % / 50 - 60 Hz

Accessories Zubehör für Autoklaven, CertoClav Alternative Tischautoklaven CertoClav EL

Small laboratory table-top autoclave with round chamber for sterilization tasks of various kinds. A hinged lid with electromotive locking mechanism in combination with the robust lip seal ensures easy and safe closing of the sterilization chamber. A temperature lock in the liquid program prevents opening at temperatures higher than 80 °C and therefore unwanted boiling delay. For an exact control the autoclave has an electronic absolute pressure sensor and a flexible temperature sensor PT100 Kl. A.

• Loading capacity: 10 media bottles or 6 Erlenmeyer flasks (500 ml)
• Safe and simple locking device
• Completely made of stainless steel
• Fits on any laboratory bench

Equipment versions
Basic Lab: With heating elements. For the sterilization of simple materials or liquids without dry removal.
Dry Lab: With heating elements, membrane-vacuum pump. For the sterilization of non-infectious waste bags and materials which require intensive subsequent drying.
Quick Lab Basic: With heating elements, water-cooling system, internal heat exchanger. For the sterilization of large quantities of liquids.
Quick Lab: With heating elements, water-cooling system, internal heat exchanger, membrane-vacuum pump. For the sterilization of non-infectious waste bags, large quantities of liquids and materials which require intensive subsequent drying.
Safe Lab: With heating elements, membrane-vacuum pump, exhaust air filtration EAF. For operation in the level S2 lab. Recommended for the sterilization of infectious waste bags and materials which require intensive subsequent drying.
Complete Lab: With heating elements, membrane-vacuum pump, exhaust air filtration EAF, water-cooling system, internal heat exchanger. Fully equipped laboratory autoclave for operation in the level S2 lab. Recommended for the sterilization of infectious waste bags, large quantities of liquids and materials which require intensive subsequent drying.

Specifications
Chamber volume:	25 l
Permissible operating pressure:	3.8 bar absolute
Permissible operating temperature:	140 °C
Heat output:	2.5 kW
Chamber dimensions (Ø x D):	300 x 360 mm
Outer dimensions (W x D x H):	450 x 640 x 525 mm
Weight basic unit:	45 kg
Power supply:	240 V, 50 Hz, 16 A

Laboratory table-top autoclave with round chamber for sterilization tasks of various kinds. A hinged lid with electromotive locking mechanism in combination with the robust lip seal ensures easy and safe closing of the sterilization chamber. A temperature lock in the liquid program prevents opening at temperatures higher than 80 °C and therefore unwanted boiling delay. For an exact control the autoclave has an electronic absolute pressure sensor and a flexible temperature sensor PT100 Kl. A.

• Loading capacity: 24 medium-flasks or 17 Erlenmeyer flasks (500 ml)
• Safe and simple locking device
• Completely made of stainless steel
• Fits on any laboratory bench

Equipment versions
Basic Lab: With heating elements. For the sterilization of simple materials or liquids without removal dry.
Dry Lab: With heating elements, membrane-vacuum pump. For the sterilization of non-infectious waste bags and materials which require intensive subsequent drying.
Quick Lab Basic: With heating elements, water-cooling system, internal heat exchanger. For the sterilization of large quantities of liquids.
Quick Lab: With heating elements, water-cooling system, internal heat exchanger, membrane-vacuum pump. For the sterilization of non-infectious waste bags, large quantities of liquids and materials which require intensive subsequent drying.
Quick Lab Advanced: With steam generator, water ring vacuum pump, water-cooling system, internal heat exchanger, air recirculation valve, steam/air mixture method (SAMM). For the sterilization of non-infectious waste bags, large quantities of liquids and materials which require intensive subsequent drying. This also applies to liquids in closed containers.
Safe Lab: With heating elements, membrane-vacuum pump, exhaust air filtration EAF. For operation in the level S2 lab. Recommended for the sterilization of infectious waste bags and materials which require intensive subsequent drying.
Complete Lab: With heating elements, membrane-vacuum pump, exhaust air filtration EAF, water-cooling system, internal heat exchanger. Fully equipped laboratory autoclave for operation in the level S2 lab. Recommended for the sterilization of infectious waste bags, large quantities of liquids and materials which require intensive subsequent drying.

Specifications
Chamber volume:	65 l
Permissible operating pressure:	3.8 bar absolute
Permissible operating temperature:	140 °C
Heat output:	6.0 kW
Chamber dimensions (W x D x H):	310 x 680 x 310 mm
Outer dimensions (W x D x H):	700 x 820 x 644 mm
Weight basic unit:	125 kg
Power supply:	400 V, 50 Hz, 16 A

Die Dampfsterilisatoren sind erhältlich mit Kammergrößen zwischen 55 l und 195 l, universelle Aufstellungsmöglichkeiten als Stand- und Tischgerät und zahlreiche Ausstattungsvarianten ermöglichen individuelle Lösungen, die Ihren spezifischen Anforderungen gerecht werden. Typische Anwendungsbereiche unserer Geräte sind alle mikrobiologischen Labore in Forschungseinrichtungen, Universitäten, Qualitätskontrollen in der Pharma- und Lebensmittelindustrie sowie der Vernichtungssterilisation, zum Beispiel im Bereich der medizinischen Diagnostik. Die Autoklaven der Serie Laboklav zeichnen sich durch Zuverlässigkeit und Qualität aus. Wir fertigen ausschließlich in Deutschland unter hohen und permanent kontrollierten Qualitätsstandards. Unsere Geräte sind zertifiziert durch den TÜV und verfügen über eine Serienzulassung. Sie entsprechen nachfolgenden Normen:

• Druckgeräterichtlinie 97/23/EU
• DIN 58950: Sterilisation - Dampf-Sterilisatoren für pharmazeutische Sterilisiergüter
• DIN 58951: Sterilisation - Dampf-Sterilisatoren für Labor-Sterilisiergüter

Kein Zubehör im Lieferumfang, nur das Gerät. Bitte bei der Bestellung die Version als Stand- oder Tischgerät angeben.

Spezifikationen	55 | 100 | 135 | 160 | 195
Kammervolumen:	55 l | 100 l | 135 l | 160 l | 195 l
Kammermaße (Ø x T):	410 x 460 mm | 410 x 760 mm | 500 x 660 mm | 500 x 760 mm | 500 x 990 mm
Außenmaße Standgerät (B x H x T):	740 x 765 x 600 mm | 740 x 1065 x 600 mm | 840 x 965 x 700 mm | 840 x 1065 x 700 mm | 840 x 1215 x 700 mm
Außenmaße Tischgerät (B x H x T):	740 x 600 x 765 mm | 740 x 600 x 1065 mm | 840 x 700 x 965 mm | 840 x 700 x 1065 mm | 840 x 700 x 1215 mm
Gewicht:	115 kg | 185 kg | 195 kg | 210 kg | 245 kg
Max. zulässiger Druck (PS):	2,8 bar
Max. zulässige Temperatur (TS):	143 °C
Heizleistung Dampferzeuger:	3-6 kW, wählbar | 6 kW, wählbar | 6-10 kW, wählbar | 6-10 kW, wählbar | 10 kW
Elektrischer Anschluss:	3N 400 V ~, 50 Hz, 16 A
Sterilisiertemperatur:	98 ... 135 °C, einstellbar

Accessories Zubehör für Dampfsterilisator Laboklav 25 Alternative Dampfsterilisator LABOKLAV 25

Maximaler Komfort zu einem geringen Preis, dafür stehen die Autoklaven der LABOKLAV ECO-Serie. Sie ermöglichen einfache Laboranwendungen wie:

• Sterilisation von Flüssigkeiten in offenen und leicht verschlossenen Gefäßen, auch mit Luftrückkühlsystem
• Instrumentensterilisation
• Vernichtungssterilisation bei 134 °C (thermische Inaktivierung)
• optionale Abluftfiltration

Spezifikationen	135
Kammervolumen:	135 l
Kammermaße (Ø x T):	500 x 660 mm
Außenmaße (B x H x T):	840 x 965 x 700 mm
Gewicht:	ca. 195 kg
Max. zulässiger Druck (PS):	2,8 bar
Max. zulässige Temperatur (TS):	143 °C
Heizleistung:	6 kW
Elektrischer Anschluss:	3N 400 V ~, 50 Hz, 16 A
Sterilisiertemperatur:	98 ... 135 °C, einstellbar

Accessories  Alternative Dampfsterilisator LABOKLAV 25 Alternative Dampfsterilisator LABOKLAV 55 - 195