Heating mantles

Not moisture-resistant. With fibre glass protective braiding. Max. surface temperature 450°C. With nickel-plated copper external braiding as protective earth conductor, 1.0 metre long mains connection cable for permanent connection to a fused 230 V outlet. Power loading approximately 200 W/m, 230 V a.c. Tape dimensions: 12 x 8 mm. Lengths as indicated.

LabHEAT^®-regulator. Freely configurable electronical temperature regulator with two displays indicating the desired and actual values. PID self-optimisation, with ramp function, USB port, for external configuration. Pt-100 or thermocouples for temperatures up to 1200 °C, metal housing (H x W x D) 75 x 205 x 140 mm with fixed support clamp, switching power max. 2300 W (10A), 1.5m power supply (earthed) cable with plug. Nominal voltage 230 V AC.

LabHEAT^® - Heating mantles for flasks, round bottom. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing with built-in power-on and heating zone switch; max. heating element temperature 450°C; 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC.

LabHEAT^® - Heating mantles for flasks, round bottom. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing with built-in power-on and heating zone switch, in addition equipped with a controller which allows a continuous adjustment of the heater power; max. heating element temperature 450°C; 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC.

LabHEAT^®-Heating mantles for flasks, round bottom. Designed and technically identical to series KM-ME, but can be used for round flasks of three different sizes, max. heating element temperature 450°C; 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC also equipped with a controller which allows a continuous adjustment of power.

Alternating current resistance controller with interference suppressor for variable, no-power-loss control of hotplates, heating tapes, soldering irons, light bulbs, infrared radiators etc., control range 25V to 225V. With single throw on/off potentiometer and shielded fuse holder for safe fuse replacement away from the internal circuit. Fitted with interference suppressor in accordance with EN standard.

LabHEAT^®-Heating mantles for flasks, round bottom. Designed identical to series KM-G, but the heating element is made of heat-resistant quartz yarn and permits a maximum temperature up to 900 °C; 1.5 m power supply (earthed) cable with heating-zone switch and RCD (residual current detection); nominal voltage 230 V AC.

LabHEAT^® - Heating mantles for flasks, round bottom. Designed and technical identical to series KM-ME, but in addition equipped with a magnetic stirrer; rotational frequency up to 1600rpm max. heating element temperature 450°C, 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC.

LabHEAT^®-Accessories for metal-cased heating mantles and serial heating unit to fix support rods up to diameter 12 mm or to integrate the metal-cased heating mantles within support wall.

LabHEAT^®-sensors. Suitable for temperature control and KM-KM-RX1001 RX1004 with permanently attached cable, with or without diode plug.

KM-TP2: Pt100, up to 400 °C, sheated element V2A, dia. 4 x 50 mm,
KM-TPG: Pt100, up to 250 °C, glass tube, dia. 6 x 40 0mm,
KM-TNS: NiCr-Ni, up to 1200 °C, rod sensor in Inconell, dia. 1.5 x 300 mm
KM-TNF: NiCr-Ni, up to 400 °C, flat sensor, 0.4 x 15 x 400 mm