Heating mantles

LabHEAT^®-Heating tapes. Very flexible. No protection against ingress of water. With inner metal protective braiding and glass fibre insulation. Max. heating element temperature: 450 °C. With power cable (1.0 m) for fixed connection, nominal voltage: 230 V AC.
Dimensions: 30 x 5 mm.

Heating mantle has a "V"-shaped design for large, pear-shaped and round-bottom flasks. The bottom opening allows 60° funnels of various diameters to be accommodated. Coiled heating element provides optimal heat transfer. Control heat throughout the mantle using three separate electrical circuits (top, middle, and bottom), each controlled with its own dial switch.

• Cool-to-the-touch design with powder-coated aluminium casing
• Indicator lamps for "power on" and "heat on" operation

Not moisture-resistant. With fibre glass protective braiding. Max. surface temperature 450°C. With nickel-plated copper external braiding as protective earth conductor, 1.0 metre long mains connection cable for permanent connection to a fused 230 V outlet. Power loading approximately 200 W/m, 230 V a.c. Tape dimensions: 12 x 8 mm. Lengths as indicated.

LabHEAT^® - Heating mantles for flasks, round bottom. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing with built-in power-on and heating zone switch; max. heating element temperature 450°C; 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC.

LabHEAT^®-Heating mantles for flasks, round bottom. Designed and technically identical to series KM-ME, but can be used for round flasks of three different sizes, max. heating element temperature 450°C; 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC also equipped with a controller which allows a continuous adjustment of power.

Alternating current resistance controller with interference suppressor for variable, no-power-loss control of hotplates, heating tapes, soldering irons, light bulbs, infrared radiators etc., control range 25V to 225V. With single throw on/off potentiometer and shielded fuse holder for safe fuse replacement away from the internal circuit. Fitted with interference suppressor in accordance with EN standard.

LabHEAT^®-Heating mantles for flasks, round bottom. Designed identical to series KM-G, but the heating element is made of heat-resistant quartz yarn and permits a maximum temperature up to 900 °C; 1.5 m power supply (earthed) cable with heating-zone switch and RCD (residual current detection); nominal voltage 230 V AC.

LabHEAT^® - Heating mantles for flasks, round bottom. Designed and technical identical to series KM-ME, but in addition equipped with a magnetic stirrer; rotational frequency up to 1600rpm max. heating element temperature 450°C, 1.5m power supply (earthed) cable and RCD (residual current detection); nominal voltage 230V AC.

LabHEAT^®-Accessories for metal-cased heating mantles and serial heating unit to fix support rods up to diameter 12 mm or to integrate the metal-cased heating mantles within support wall.

LabHEAT^®-sensors. Suitable for temperature control and KM-KM-RX1001 RX1004 with permanently attached cable, with or without diode plug.

KM-TP2: Pt100, up to 400 °C, sheated element V2A, dia. 4 x 50 mm,
KM-TPG: Pt100, up to 250 °C, glass tube, dia. 6 x 40 0mm,
KM-TNS: NiCr-Ni, up to 1200 °C, rod sensor in Inconell, dia. 1.5 x 300 mm
KM-TNF: NiCr-Ni, up to 400 °C, flat sensor, 0.4 x 15 x 400 mm