Bags, Foils

Seal-R-film™ sealing film seals beakers, flasks, and other vessels. The sealing film can be stretched to three times its original length and therefore fits even irregular shapes.

• Protects against evaporation, leakage, and contamination
• Lot identification of each roll

Non-slip Laboratory mats with 2 different sides for organising and thus simplyfying workflow processes. One side with a completely flat surface and one side with a combination of gridded and flat surface. The gridded area avoids unwanted movement of small parts
Ideal for all laboratories and more specialised areas such as cold rooms or areas with high sterility requirements such as clean rooms. Dimensions (W x D x H): 305 x 379 x 2 mm

• Protection of the work bench from hot items up to 200 °C
• Lip around the edge can hold approx. 250 ml of liquid
• Reusable
• Chemically resistant
• Dishwasher safe
• Food safe
• Noise dampening
• Can be rolled up
• Autoclavable at 121 °C for 15 minutes

For micro test plates, deep well plates, micro test tubes and 96/384 Well PCR plates. DMSO resistant.

• For manual use
• Temperature resistant from -80 to 120 °C
• Adhesive of PP and aluminium foils with high solvent and DMSO resistance
• All films in SBS standard format

For transporting or keeping food fresh.

• Tearproof
• Heat resistant
• Easy handling by tear-off saw
• Also available extra wide

This blender bag is ready-to-use with a lateral non-woven filter, which includes a dehydrated pre-dosed media. This enables media preparation and sample preparation for microbiological analyses as two processes in one step. Ideal for selective enrichment.

• No contact between the sample and the blender during homogenization
• Multilayer^®: multicoated reinforced complex
• Rigid and transparent
• For all types of sample (fibrous, pasty, etc.)
• Pipetting directly from the bag
• Compatible with any 400 ml blender

instaBAG^® Fraser ½: With medium for primary selective enrichment or as a diluent for the detection and enumeration of Listeria monocytogenes and Listeria spp. (ISO 11290Ý 1, ISO 11290 2) in food and environmental samples.

instaBAG^® BPW: With buffered peptone water for the dilution of samples for the enumeration of all microorganisms (ISO 6887), in the ISO 11290-2 standard as a diluent for the enumeration of Listeria Monocytogenes and for non-selective pre-enrichment for Salmonella spp (ISO 6579) and Enterobacteria (ISO 21528-1) detection.

Transparent. For collecting, storing, closing and protecting substances and small laboratory parts. The bags have a "zipper" with double grooves for safe closing.

Protect benches and other surfaces against liquid spills with the highly absorbent Thermo Scientific™ Sterilin™ BenchGuard.

• Available in both 400mL/m2 and 800mL/m2 absorption capacities
• Plastic coated on one side to prevent soak through
• Available in roll or sheet form
• Rolls supplied in easy to use dispenser packs

Alternative Benchkote surface protector® Alternative Bench protector, Labmat™ Alternative Bench protection paper, LabSorb

The fixing tie grips the edge of the waste bin firmly and prevents the bag from slipping into the bin. When disposing of the load, the tie is simply interlocked and used as carrying handle. Bags are opaque silver-grey, tear-resistant 3-ply film with leakproof base. Made of 80% recycled plastic.

Alternative Waste Bags, HDPE

For polyethylene films up to 2 x 0.40 mm thickness.

Seal width:	3 mm
Current input 401 M: 601 M:	3.0 A 7.0 A
Power consumption 401 M: 601 M:	0.8 kWh 1.5 kWh
Mains supply:	230 V / 50 Hz

Accessories Plastic film, rolls

In case the microplates, PCR- and Deepwellplates need not only to be covered, but also securely sealed, self-adhesive sealing films are available. These film sheets can be easily applied on the plates and removed also without the use of expensive equipment. They are available in different versions and are especially well-suited for storage or cell- and tissue-culture.

Ideal for using as table pad or for lining drawers. Also suitable for using as slideway or for insulation. White foil with universal chemical resistance, temperature resistance from -200 to 250 °C.
Rolls of 1 m.

For welding all polyethylene, polypropylene, cellulose or polyamide foils up to a thickness of 2 x 0.25 mm. Expandable with a plug-in table and a film roll-off device. M model sealers have an additional holding magnet as well as a welding and cooling automatic.

Specifications
Sealing length:	250 mm
Sealing width:	1.5 mm
Power consumption: Power output:	0,6 A / 1,2 A* 0,14 kWh / 0,28 kWh*
Dimensions:	420 x 120 x 135 mm
Power supply:	230 V, 50 Hz

For welding all polyethylene, polypropylene, cellulose or polyamide foils up to a thickness of 2 x 0.25 mm. Expandable with a plug-in table and a film roll-off device. With cutting device and double-sided heating tape clamping device. M model sealers have an additional holding magnet as well as a welding and cooling automatic.

Specifications	423 M / 583
Sealing length:	440 mm / 600 mm
Sealing width:	1.5 mm
Power consumption: Power output:	1.3 A 0.29 kWh / 0.3 kWh
Dimensions:	720 x 120 x 135 mm / 880 x 120 x 135 mm
Power supply:	230 V, 50 Hz

• Diamond-shaped PTFE mesh sheeting is 1.6 mm thick with 6 mm openings
• Corrosion and break-resistant lining
• Useful as mesh bag for dipping parts in corrosive chemicals and solvents
• Easy to clean

The double layer enables total protection of surfaces in the laboratory, thanks to its waterproof polyethylene layer that prevents liquids from reaching the protected surface.

• Cellulose layer: pure filter paper enables a large quantity of liquids to be absorbed.
• Polyethylene layer: totally waterproof, prevents liquids from reaching the protected surface
• The high purity of the filter paper allows for recovery of the spilt liquids
• Weight 120 g/m², Thickness 0.2 mm, absorbs 110 g/m²

Alternative LLG-Surface protector DescProtect

Made of very strong PP-film with a broad seam at the bottom, for the disposal of contaminated labware. Autoclavable at 134 °C. Imprinted with warning labels and sterilisation indicator.

Please order stand separately.

Accessories Bench-top stand for waste disposal bags

Whirl-Pak® bags are sterile polyethylene laboratory sample bags used to transport samples for biological testing and other applications.
Temperature range -210 to 82 °C.
Made of black pigmented PE-film providing maximum protection for samples that are sensitive to light.