Heating mantles

Filter

 Standard heating mantles series KM-G

SAF

LabHEAT ®-Heating mantles for flasks, round bottom. Flexible glass yarn heating element, outer jacket in glass silk, with diam. 60 mm bottom out-let from 500 ml, max. heating element temperature 450 °C, 1.5 m power supply (earthed) cable with heating-zone switch and RCD (residual current detection)....

 Power controller KM-L116 for heating mantles

SAF

LabHEAT ®-regulator for heating mantles. Electromechanical; infinitely variable control over power outlet; plastic housing (H x W x D) 55 x 65 x 120 mm; switching power max. 2990 W (13 A); 1.5 m power supply (earthed) cable with plug....

 Electronic heating mantles HM-200

electrotherm

Polypropylene outer case is resilient and chemically resistant. Highly efficient in heating up to a maximum element temperature of 450 °C. The flexible heating element is suspended in a thermal insulating cartridge to provide maximum heat transfer with minimum risk of flask breakage. Even at full power output, the exterior remains "cool-to-touch" due to good heating element insulation. All heating mantles have support clamp for rods of up to 12 mm diameter, and are double fused, with earth (ground) screen to protect the user from electric shocks....

 Laboratory regulator series KM-RX1000

SAF

LabHEAT ®-regulator. Freely configurable electronical temperature regulator with two displays indicating the desired and actual values. PID self-optimisation, with ramp function, USB port, for external configuration. Pt-100 or thermocouples for temperatures up to 1200 °C, metal housing (H x W x D) 75 x 205 x 140 mm with fixed support clamp, switching power max. 2300 W (10A), 1.5m power supply (earthed) cable with plug. Nominal voltage 230 V AC....

 Accessories for Standard heating mantles

SAF

LabHEAT ® - Accessories made of stainless steel (1.4301) for higher stability or to integrate within support wall. The heating mantles are able to be suspended on its four clips....

 Electronic multi-size heating mantles HM-200-SP, spill-proof

electrotherm

Solid stainless steel liner, which protects against fluid spills and is easy to clean, with central aperture to accommodate round-bottom and pear-shaped flask and 60° funnels. For round bottom flasks, pear-shaped flasks and 60° funnels (Mantle is open at the bottom). Polypropylene outer case is resilient and chemically- resistant. Highly efficient in heating up to an element temperature of 450 °C. Even at full power output, the exterior remains "cool-to-touch" due to good heating element insulation. All heating mantles have support clamp for rods of up to 12 mm diameter, and are double fused, with earth (ground) screen to protect the user from electric shocks....

 Electronic multi-size heating mantles HM-200-V, V-shaped

electrotherm

Solid, with mesh stainless steel liner, which protects against fluid spills, with central aperture to accommodate round-bottom and pear-shaped flask and 60° funnels. For round bottom flasks, pear-shaped flasks and 60° funnels (Mantle is open at the bottom). Polypropylene outer case is resilient and chemically- resistant. Highly efficient in heating up to a maximum element temperature of 450 °C. Even at full power output, the exterior remains "cool-to-touch" due to good heating element insulation. All heating mantles have support clamp for rods of up to 12 mm diameter, and are double fused, with earth (ground) screen to protect the user from electric shocks....

 Electronic stirrer mantles SHM-200 series

Carl Stuart Limited

Built-in adjustable heater control up to an element temperature of 450 °C and magnetic stirring control up to approx. 520 rpm with auto-reverse facility and automatic stirrer bar trap; the stirrer unit has an independent power supply. Polypropylene outer case is resilient and chemically-resistant. Even at full power output, the exterior remains ''cool-to-touch'' due to good heating element insulation. All heating mantles have support clamp for rods of up to 12 mm diameter, and are double fused, with earth (ground) screen to protect the user from electric shocks....

 Glass fibre-insulated heating cables series KM-HC-G

SAF

LabHEAT ®-Heating cables. No protection against ingress of water; glass fibre insulation without protective braiding; outer diameters from 3.5 to 4.5 mm; min. bending radius > 5 mm; max. heating element temperature 450 °C; preterminated with 2 x 1.5 m cold end....

 Glass fibre-insulated heating tapes series KM-HT-BS30

SAF

LabHEAT ®-Heating tapes. Very flexible. No protection against ingress of water. With inner metal protective braiding and glass fibre insulation. With power cable (1.0 m) for fixed connection....

 Heating mantles Electrothermal® MHM-200

electrotherm

Heating mantle has a "V"-shaped design for large, pear-shaped and round-bottom flasks. The bottom opening allows 60° funnels of various diameters to be accommodated. Coiled heating element provides optimal heat transfer. Control heat throughout the mantle using three separate electrical circuits (top, middle, and bottom), each controlled with its own dial switch....

 Heating tapes, fibre glass, KM-HT-G series

SAF

Not moisture-resistant. With fibre glass protective braiding. Max. surface temperature 450 °C. With nickel-plated copper external braiding as protective earth conductor, 1.0 metre long mains connection cable for permanent connection to a fused outlet. Power loading approximately 200 W/m....

 Metal-cased heating mantles series KM-M, without controller

SAF

LabHEAT ® - Heating mantles for flasks, round bottom. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing with built-in power-on and heating zone switch; max. heating element temperature 450 °C; 1.5 m power supply (earthed) cable and RCD (residual current detection)....

 Metal-cased heating mantles series KM-ME, with controller

SAF

LabHEAT ® - Heating mantles for flasks, round bottom. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing with built-in power-on and heating zone switch, in addition equipped with a controller which allows a continuous adjustment of the heater power; max. heating element temperature 450 °C; 1.5 m power supply (earthed) cable and RCD (residual current detection)....

 Multi-size Heating Mantles, series KM-MPE for different sized round bottom flasks

SAF

LabHEAT ®-Heating mantles for flasks, round bottom. Designed and technically identical to series KM-ME, but can be used for round flasks of three different sizes, max. heating element temperature 450 °C; 1.5 m power supply (earthed) cable and RCD (residual current detection), equipped with a controller which allows a continuous adjustment of power....

 Power controller, Voltron 20

messner

Alternating current resistance controller with interference suppressor for variable, no-power-loss control of hotplates, heating tapes, soldering irons, light bulbs, infrared radiators etc., control range 25V to 225V. With single throw on/off potentiometer and shielded fuse holder for safe fuse replacement away from the internal circuit. Fitted with interference suppressor in accordance with EN standard....

 Standard heating mantles series KM-GH

SAF

LabHEAT ®-Heating mantles for flasks, round bottom. Designed identical to series KM-G, but the heating element is made of heat-resistant quartz yarn and permits a maximum temperature up to 900 °C; 1.5 m power supply (earthed) cable with heating-zone switch and RCD (residual current detection)....

 Stirring heating mantles LabHEAT® KM-MER series

SAF

LabHEAT ® - Heating mantles for flasks, round bottom. Designed and technical identical to series KM-ME, but in addition equipped with a magnetic stirrer; rotational frequency up to 1600 rpm max. heating element temperature 450 °C, 1.5 m power supply (earthed) cable and RCD (residual current detection)....

 Support clamp KM-SK

SAF

LabHEAT ®-Accessories for metal-cased heating mantles and serial heating unit to fix support rods up to diameter 12 mm or to integrate the metal-cased heating mantles within support wall....

 Temperature sensors for Laboratory regulator series KM-RX

SAF

LabHEAT ®-sensors. Suitable for temperature control and KM-KM-RX1001 RX1004 with permanently attached cable, with or without diode plug.

KM-TP2: Pt100, up to 400 °C, sheated element V2A, dia. 4 x 50 mm,
KM-TPG: Pt100, up to 250 °C, glass tube, dia. 6 x 40 0mm,
KM-TNS: NiCr-Ni, up to 1200 °C, rod sensor in Inconell, dia. 1.5 x 300 mm...

 Heating tapes series KM-HT-201

SAF

Silicone insulated heating tape up to 200 °C.

  • Waterproof
  • Very flexible
  • Easy to clean
  • Suitable for food production
  • Without protective conductor
...

 Insulating mantles KM-IRB series

SAF

Insulating mantles for single and double neck round bottom flasks, heated insulating mantles with glass yarn element (max. 450 °C) and grounding.

  • Made by hand work
  • Aluminium coated outer jacket
  • Thermally insulated
  • To prevent heat losses occuring at the upper flask halves
...

 Insulating mantles KM-IRU series

SAF

Insulating mantles for single and double neck round bottom flasks. To prevent heat losses occuring at the upper flask halves.

  • Made by hand work
  • Aluminium coated outer jacket
  • Thermally insulated
...

 Metal-cased heating mantles series KM-MHB

SAF

LabHEAT ® - Heating mantles for high form beakers. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing, with built-in power-on and heating zone switch, max. heating element temperature 450 °C; 1.5 m power supply (earthed) cable and RCD (residual current detection)....

 Metal-cased heating mantles series KM-MNB

SAF

LabHEAT ® - Heating mantles for low form beakers. Flexible glass yarn heating element in plastic coated, chemical-resistant metal housing, with built-in power-on and heating zone switch, max. heating element temperature 450 °C; 1.5 m power supply (earthed) cable and RCD (residual current detection).....

Add to shopping cart