Special Photometers

Please Note: These products will only operate with the correct type of air compressor and gas regulator as specified below.

Single channel, low temperature flame photometer for use in industry, medicine and education. Can be operated with propane, butane, natural gas or liquid gas (LPG). With built-in electronic flame failure safety system for operational safety.

• Model PFP7 incl. Na, K, Ca, Ba and Li filters
• Model PFP7/C incl. Na, K and Li filters
• 3 year warranty

Supplied with: Na, K, Li filters (model PFP7/C), additionally Ba and Ca filter (model PFP7), connecting hoses and clips, compressor plug, drain trap, fuses and operating/service instructions

Specifications
Range PFP7: Range PFP7/C: Limits of detection Na/K: Li: Ca: Ba:	0 ... 199.9 ppm 120 ... 160 ppm Na, 0 ... 10 ppm K < 0.2 ppm < 0.25 ppm < 15 ppm < 30 ppm
Reproducibility:	< 1 % (Coefficient of variation for 20 consecutive samples using 10 ppm Na set to a reading of 50)
Linearity:	< 2 % (when concentration of 3 ppm Na/K and 5 ppm Li are set to a reading of 100)
Specificity:	Interference from Na, K and Li equal in concentration to test element will be < 0.5 %
Recorder output:	Nominal 1.00 V for a reading of 100.0
Air:	6 l/min at 1 Kg/cm2 /14psi (oil and moisture free pressurised air)
Dimensions (W x D x H): Weight:	420 x 360 x 300 mm 8 kg
Power supply:	190 ... 250 V, 50/60 Hz

Accessories Accessories to Flame Photometer PFP7

The compact photometer PF-12^Plusis a customized device for mobile water analysis, which is used to evaluate the proven VISOCOLOR^® ECO tests and NANOCOLOR^® tube tests by MACHEREY-NAGEL. This filter photometer with microprocessor control, self-test and auto-calibration is suitable for mobile analytics. It is equipped with more than 100 preprogrammed methods and additional functions. An 860 nm LED allows the nephelometric turbidity measurement in the range of 1 to 1000 NTU. The icon-based menu navigation and the clear task bar make the PF-12^Plusan easy-to-use photometer for all applications in water and waste water analysis. Numerous other variants of the VISOCOLOR^® and NANOCOLOR^® reagent cases are available in combination with the PF-12^Plus.

• With over 100 preprogrammed tests and special methods, extinction, transmission, factor, standard, nephelometric turbidity measurement (NTU-Check), 50 freely programmable methods
• 7 interference filter with a receptacle for an additional filter, 860 nm LED for NTU measurement
• Insensitive to external light for fast measurement without cuvette slot cover
• Xenon high-pressure lamp
• Automatic zero balance
• Fully automatic turbidity control at 90° angle (NTU-Check)
• Free updates

Scope of delivery: Compact photometer PF-12^Plusincl. Software DVD, manual, 4 batteries, 4 empty cuvettes, funnel, cup, syringe, USB cable, calibration cuvette, certificate and cleaning cloth in a sturdy case

Specifications
Optics:	Automatic filter wheel with 7 interference filters
Wavelengths:	345 nm / 436 nm / 470 nm / 540 nm / 585 nm / 620 nm / 690 nm / 860 nm
Wavelength accuracy:	± 2 nm, bandwidth at half transmission 10 ... 12 nm
Photometric range / accuracy:	± 3 A / ± 1 %
Stability:	<0.002 A/h
Data memory:	1000 results, GLP conform
Cuvette slot:	Round cuvettes 16 mm OD
Display:	Backlit graphic display, 128 x 64 pixels
Interface:	USB 2.0
Environmental conditions:	10 ... 40 °C, up to 80 % relative humidity (non-condensing)
Dimensions (W x D x H):	215 x 100 x 65 mm
Weight:	700 g
Power supply:	USB interface, batteries, rechargeable batteries or accu-pack
IP code:	IP 68

The Lovibond^® MD 100 Photometers are designed for analysis of different parameters in drinking water, industrial process water and waste water. With a total of more than 30 different types, instruments are available for routine testing as well as for special applications. The MD 100 uses high quality interference filters with long-life LEDs as a light source without any moving parts in a transparent sample chamber. The units supply accurate, reproducible results very quickly. Other major advantages include ease of operation, ergonomic design, compact dimensions and safe handling. Provided with calibration and software-based adjustment options the MD 100 is suitable for use as a testing instrument. The tests are conducted using either Lovibond^® tablet reagents with long-term stability and a shelf life of 5 or 10 years, VARIO powder reagents or using liquid reagents.

• Optics: High-quality Interference Filters
• Wavelength accuracy: ±1 nm.
• Power supply: 4 micro batteries (AAA), capacity approx. 17 hours or 5000 tests.
• Automatic switch-off.
• LCD Display (backlit on keypress).
• Internal ring memory for 16 data sets.
• Dimensions (L x W x H): 155 x 75 x 35 mm.

Scope of supply: Photometer in a plastic carrying case, with reagents for 100 tests, cells, batteries and standard accessories.
Optional: IRiM - infrared interface module for data transfer to computer or printer.

Alternative Photometers AL100 Boiler Water, Cooling Water

COD measurement without reagents.
The spectrophotometer of the photoLab^® 7000 Series are universally usable and offer complete photometric
functionality with lauded user-interface and guidance on a brilliant HD 7"" color display. Pioneering is the optical reagent-free measurement (OptRF) of COD, Nitrate and Nitrite. No time-consuming digestion and no harmful chemicals required.

• Proven routine analysis for waste and drinking water, aquaculture, food & beverage, environmental monitoring and production
• Cost saving reagent-free OptRF measurement
• Universal for industrial, research and educational use
• Lab quality in the field: 4,5 kg light weight, with car battery and field case option
• Linking lab with Online-system WTW^® IQ SENSORNET via IQ LabLink
• For 16 mm round cuvettes and 10, 20 and 50 mm rectangular cuvettes with automatic recognition
• Memory for 5000 values, spectra and kinetics approx. 40 MB, equivalent to approx. 500 spectra (300-900 nm) and 400 kinetics with 150 measured values
• More than 200 programmed methods, 1000 user defined methods, 20 profiles each for kinetics and absorption spectrum, extensive programming options

Routine Analysis:

• More than 250 programs for commercial test kits, standard parameters, direct readings of coloration, SAK, etc. as well as user-defined programming of routines
• Barcode recognition for tests in vials and rectangular cells and automatic cell recognition for 16, 10, 20 and 50 mm without adapter and automatic measurement range selection
• Up to three parallel timers
• Optional PC-Software Package for Brewery and color measurement from CIE to Yellowness

Spectral and universal analysis from 190 to 1100 nm:

• Spectral scans in various nm-steps, 700-2000 nm/min
• Kinetics and multi-wavelength readings including special methods like chlorophyll and ADMI color measurement
• Extensive programming tools for multistep and multi-wavelength functions with user guidance

AQA: Multi-level user-friendly AQA functions with administration tools and comprehensive checking aids for meter and reagents.
Data Management:

• Measurement data, PDF documents, spectra and kinetics data, with data filter for pre-selected data management
• External barcode reading option for uncoded test kits and sample ID
• Optional: PC-Software for GLP compliant data management

Specifications
Optics:	Split beam
Wavelength range:	320 to 1100 nm (VIS) / 190 to 1100 nm (UV-VIS)
Bandwidth:	4 nm
Lamp:	Tungsten Halogen (VIS)/ Xenon Flashlamp (UV-VIS)
Display:	Colour, 7" backlit
Wavelength accuracy / reproducibility:	±1 nm / <0.5 nm (VIS and UV-VIS)
Photometric accuracy / reproducibility:	-0.003 E for E < 0.600 / 0.5% of values for 0.600
Interface / Update:	1 USB-A, 1 USB-B, 1 Ethernet / Update via Internet and USB-Stick
Temperature range:	Operation: +10 °C to +35 °C, Storage: -25 °C to +65 °C
Dimensions (W x D x H):	404 x 314 x 197 mm
Weight:	approx. 4.5 kg
IP code:	IP 30

Suitable for calibration, control, IQ / OQ and method validation. Compatible with all Flame Photometry Instruments. Available as single element analytical standards (in ppm) or Multi-element clinical standards (in mmol/l). NIST traceable. HDPE bottles of 500 ml.

The LED Photometer PF-3 with micro processor control for evaluation of pre-programmed NANOCOLOR^® and VISOCOLOR^® ECO tests is ideally suited for mobile operation directly on site in the swimming pool.

• Add new tests and parameters anytime
• Self-test and auto calibration
• Insensitive to external light for fast measurement without cuvette slot cover
• Test selection from parameter lists
• Waterproof and sturdy
• Free software for data export

Scope of delivery: Photometer PF-3 in VISOCOLOR^® reagent case with VISOCOLOR^® ECO Chlorine 2 free + total (liquid), pH 6.0 - 8.2, cyanuric acid, alkalinity TA incl. calibration cuvette, 4 empty cuvettes, sample cup, 5 ml syringe, 3 batteries, manual, booklet "VISOCOLOR^® ECO Test Instructions for Compact Photometer PF-3" and certificate in a sturdy case.

Specifications
Optics:	LED with 3 interference filters
Wavelengths:	450 nm / 530 nm / 590 nm
Wavelength accuracy:	± 2 nm, bandwidth at half transmission 10 ... 12 nm
Data memory:	50 results
Cuvette slot:	Round cuvettes 16 mm OD
Display:	Backlit graphic display, 128 x 64 pixels
Interface:	Mini-USB
Dimensions (W x D x H):	170 x 95 x 68 mm
Weight:	500 g
Power supply:	USB interface, batteries, rechargeable batteries or accu-pack
IP code:	IP 68

Accessories Photometer NANOCOLOR® VIS II / NANOCOLOR® UV/VIS II Alternative

Accessories Photometer NANOCOLOR® VIS II / NANOCOLOR® UV/VIS II

Reflectance photometer for the evaluation of test strips
Programmed for QUANTOFIX test strips. The system simplifies testing procedures and the decision processes by eliminating the subjectivity of visual readings and by providing higher accuracy.

• Touch-Display
• 5 methods preset, any other methods can be selected
• Autostart function
• Measured value output in the display
• Fixed power supply and battery operation
• Memory for 200 measurements
• No gradation and estimation of in-between values is necessary
• Very simple operation, precise results
• Printing and data transfer, simple documentation
• Output of intermediate values

Specifications
Dimensions (W x D x H ):	160 x 200 x 75 mm
Weight:	710 g
Power requirements:	Netzteil 110 ... 240 V AC Batteriebetrieb mit 6 AA Batterien

As complete spectrophotometers, the NANOCOLOR^® VIS II and NANOCOLOR^® UV/VIS II meet all requirements of your daily laboratory work. They come with the well-known barcode technology for NANOCOLOR^® tube tests for fast measurements. Besides, they offer the possibility of extensive CIE-conform color measurements and scan-performance in real time. In addition to turbidity measurements, the devices offer comprehensive and free of charge brewery analysis according to MEBAK.

NANOCOLOR^® VIS II and NANOCOLOR^® UV/VIS II reduce the complexity of your daily laboratory work with easy menu guidance and icon-based procedures of the cuvette tests stored in the instrument. The clear result window enables an easy assignment of sample information to the measurement result. The step-by-step menu guidance for the calibration of special methods creates a simple entry level into user specific analytics even for inexperienced users.

Scope of delivery: Spectrophotometers, the NANOCOLOR^® VIS II or NANOCOLOR^® UV/VIS IIincl. manual (Quickstart guide), protective covering, power cable, USB cable, USB stick, calibration cuvette, touchpen, cleaning cloth and certificate

Specifications
Optical System:	Monochromator
Display:	10.1" HD display, anti-reflective cover glass with projective-capacitive touch screen (PCAP) and background LED lighting
Photometric accuracy:	0.005 E at 0.0 - 0.5 E; 1 % at 0.5 - 2.0 E
Wavelength range NANOCOLOR® VIS II: NANOCOLOR® UV/VIS II:	320 - 1100 nm 190 - 1100 nm
Wellenlängengenauigkeit:	±1 nm
Lichtquelle:	Halogen lamp
Speicher:	16 GB Micro SDHC card, 5000 measured data sets / spectra, GLP conform
Schnittstellen:	LAN, 2 x USB (Host), 1 x USB (Function) and RS 232
Netzanschluss NANOCOLOR® VIS II NANOCOLOR® UV/VIS II	12 V DC 3A 110 13240 V, ~50/60 Hz

Alternative Spectrophotometer DR 3900

The compact infrared turbidity meter TB 211 IR is designed to allow fast, precise on-site testing. The unit measures the scattered light at an angle of 90°, as stipulated in EN ISO 7027. The wide measuring range from 0.01 to 1100 TE/F = NTU = FNU permits use of the unit for various media, ranging from drinking water to waste water.
As infrared light is used for measurement, the unit can be used to test both coloured and colourless liquids. The standards required for calibration of the unit are also supplied. A second adjustment mode allows alternative adjustment with user-defined turbidity standards.

• measuring ranges from 0.01 to 1100NTU (autorange)
• measurement with infrared light at an angle of 90°
• easy operation
• 600 tests between battery charges

Scope of supply: Turbidity meter, 4 turbidity standards <0.1, 20, 200 and 800NTU, battery, USB cable (1.5 m), test vial, manual, warranty statement, case

Specifications:
Measurement cycle:	approx. 9 seconds
Display / Function:	LCD
Optics:	temperature-compensated LED and photosensor amplifier in waterproof sample chamber
Keypad: Measuring range:	4 key polycarbonate membrane 0.01 to 1100NTU (autorange)
Resolution:	0.01 to 9.99NTU = 0.01NTU 10.0 to 99.9NTU = 0.1NTU 100 to 1100NTU = 1NTU
Accuracy:	±2.5 % of measuring value or ±0.01 NTU (0 to 500 NTU) ±5 % (500 to 1100NTU)
Interface: Housing: Dimensions (L x W x H):	Micro USB ABS 190 x 110 x 55mm
Weight (Basis unit):	approx. 0.4kg
Temperature:	0 to 40°C
Humidity (rel.):	30 to 90 % R.H.
CE-conformity:	DIN EN 50081-1, VDE 0839 part 81-1:1993-03, DIN EN 50082-2, VDE 0839 part 82-02:1996-02

Accessories Accessories for turbidity meter TB 211 IR Alternative Laboratory turbidimeter TB 300 IR

VISOCOLOR^® ECO reagent case
For mobile use with test instructions for visual determination, analytical accessories and the following tests:
Ammonium 0.2 - 3mg/L NH₄⁺ / Carbonate Hardness 1 drop = 1.25°e / total hardness 1 drop = 1.25°e / Nitrate 1 - 120mg/L NO₃^- / Nitrite 0.02 - 0.5mg/L NO₂^- / pH 4.0 - 9.0 / Phosphate 0.2 - 5mg/L P

VISOCOLOR^® reagent case for soil analysis
The VISOCOLOR^® reagent case for soil analysis is the perfect companion for economical, fast and convenient soil analysis, both in the field or in your laboratory, including the following tests:
QUANTOFIX^® test strips: Ammonium 10 - 400mg/L NH₄⁺ / Nitrate / Nitrite 10 - 500mg/L NO₃^-/ 1 - 80mg/L NO₂^- / VISOCOLOR^® ECO test kits: Potassium 2 - 15mg/L K⁺ / VISOCOLOR^® HE test kits: pH 4.0 - 10.0 / Phosphate 1.0 - 20.0mg/L P / pH-Fix test strip: pH 2.0 - 9.0

VISOCOLOR^® School reagent case
The VISOCOLOR^® SCHOOL reagent case is especially designed for schools and caters to the needs of both students and teachers. All reagents are approved to be used in schools in Germany (GUV - SR 2004 directive) and can be disposed of easily just down the drain without any harm to the environment.
Ammonium 0.2 - 3mg/L NH₄⁺, Nitrate 1 - 90mg/L NO₃^-, Nitrite 0.02 - 0.5mg/L NO₂^-, Phosphate 0.5 - 15mg/L P, pH pH 4.0 - 9.0, Total hardness 1 drop = 17.8mg/L CaCO₃

VISOCOLOR^® Reagent case for environmental analysis with photometer PF-12^Plus:
User guidance in 12 languages (DE, EN, FR, ES, IT, NL, HU, PL, PT, CZ, ID, SL, TR, MY)
For determination of VISOCOLOR^® ECO Ammonium 15, VISOCOLOR^® HE Carbonate hardness C 20, VISOCOLOR^® ECO Iron 2, VISOCOLOR^® HE total-Hardness H 20 F, VISOCOLOR^® ECO Nitrate, VISOCOLOR^® ECO Nitrite, VISOCOLOR^® ECO pH 4.0-9.0 and VISOCOLOR^® ECO Phosphate

Specifications PF-12Plus: Light source: Detector:	Xenon lamp Silicon photo-element
Display:	Backlit graphic display, 128 x 64 pixels All important data at a glance: Result in respective unit, date, time, sample number, sample location and dilution
Operation:	Display user guidance, plastic foil keyboard Test selection via parameter lists.
Accuracy: Long-term stability: Interface:	±1% < 0.002A/h USB 2.0
Power supply:	Via USB power supply, standard or rechargeable batteries or Akkupack
Dimensions: Weight:	215 x 100 x 65mm 0.7kg