Electrodes for conductivity measurement

For all pocket measuring devices for analog measuring cells from the 3xx series, as well as all inoLab laboratory measuring devices for analog measuring cells.

Standard conductivity cell probe TetraCon^® 325:
4-pole cell with integral temperature sensor. Measuring range: 1µS/cm to 2S/cm.

Special conductivity cell probe TetraCon^® 325/C:
As TetraCon^® 325, 4-pole cell with integral temperature sensor, but with sensor head made of chemically resistant PEEK. Measuring range: 1µS/cm to 2S/cm

For connection to WTW IDS measuring instruments.

IDS conductivity cell probe TetraCon^® 925:
Intelligent digital 4-pole cell with integral temperature sensor. Automatical transfer of the cell constant. Cable length 1.5 metres. Measuring range: 1µS/cm to 2S/cm.
TetraCon^® 925-3:
Like TetraCon^® 925, but cable length 3 m

IDS conductivity cell probe TetraCon^® 925/LV:
Intelligent digital 4-pole cell with integral temperature sensor. Fork design, suitable for small volumes (at least 2.5ml) as well as for viscous samples. Automatical transfer of the cell constant. Cable length 1.5 metres. Measuring range: 1µS/cm to 2S/cm.

IDS conductivity cell probe LR 925/01:
Intelligent digital 2-pole cell with integral temperature sensor and flowthrough cell D 01/T for measuring of low conductivity values (<1µS/cm) e.g. in boiler feed water or ion exchange water. Automatical transfer of the cell constant. Cable length 1.5 metres. Min./max. immersion depth 35/110mm and flow through measurement. Measuring range: 0.01µS/cm to 200µS/cm.

710: 4 platinum poles
720 + 751-4 + 752-6: 2 platinum poles
731 + 738: 4 graphite poles
741 + 742: 2 steel poles
ISM^® (Intelligent Sensor Management) is a sophisticated safety concept that leaves nothing to chance. The instrument automatically detects the connected sensor and uses the most up-to-date calibration data stored on the sensor chip.

All Conductivity sensors with integrated probe sensor (NTC 30 kΩ), shaft length 120 mm, schaft diameter 12 mm, only type 751-4 has diam. 4 mm and 752-6 diam. 6 mm.

With integrated reference electrode. Easy cleaning of the diaphragm between measurements with Click & Clear™ (except Na electrode): by pressing the electrode head, the electrolyte solution flows through the diaphragm. The electrolyte can be easily emptied and refilled. Optimum contact between sample and electrolyte solution is always guaranteed.

Scope of supply: Sensor with permanently connected 1.2 m cable with BNC connection, 60 ml reference electrolyte, operating instructions

Scope of supply Na-electrode: Sensor with S7 plug head, diaphragm made of glass with higher sensitivity to sodium, 25 ml reference electrolyte, operating instructions

Combined ISE and GSE electrodes.

Accessories Replacement heads for Ion-selective electrodes inoLab®

For all Cond handheld meters for analogue measuring cells from the 3xx series, as well as all inoLab^® laboratory measuring devices for analogue measuring cells. Except for the Cond 3110, Multi 340 handheld meters.

Ultra-pure water conductivity cell probe LR 325/01:
With integral temperature sensor and flowthrough vessel D 01/T for measuring very low conductivity ranges (<1 µS/cm) e.g. boiler feed water or deionised water. Cable length 1.5 metres. Min. / max. insertion depth 35 / 110mm and flowthrough, measuring range: 0.001µS/cm to 200µS/cm.

Conductivity flowthrough cell TetraCon^® DU/T:
4-pole conductivity cell with integral temperature sensor for standard applications. Connection via 10mm diameter tubing nozzles (the adapter cable KKDU with 1 metre cable is required for connection). Filling volume 7ml. Measuring range: 1µS/cm to 1000µS/cm.

With plastic shaft and internal temperature sensor NTC30 kOhm, temperature range -5 to 80 °C. Cable with 8-pole plug.

LF 435 T: Conductivity measuring cells with 4 electrode technique for a large measuring range of 5 µS/cm to 500 mS/cm, low maintanance and easy cleaning. For general measurements. With 1.5 m cable.

• Excellent linearity over a wide measuring range, especially for high conductivity values
• Easy cleaning
• Long term stable cell constant through abrasion resistant, concentric graphite electrodes
• Integrated temperature sensor with short response time for automatic temperature compensation

LF 513 T: For field and laboratory measurments of 1 µS/cm to 200 mS/cm. 2 electrode measuring technique with platinized ring electrodes. Easy cleaning through removable low shaft ending. With 1 m cable.

LF 613 T: For field and laboratory measurments in a measuring range of 1 µS/cm to 2000 mS/cm. Less polarisation effects through 4 electrode measuring technique with platinum ring electrodes. Easy cleaning through removable low shaft ending. With 1 m cable.

With spear-tip membrane. With glass shaft, Argenthal™ reference system and S7 plug head.

Cable - please order separately.

Specifications
Temperature range:	0 ... 80 °C
pH range:	0 ... 11 pH
Temperature sensor:	no
Length / Diam.:	25 mm / 6 mm
Electrolyte:	XEROLYT® PLUS polymer electrolyte, non-refillable
Diaphragm:	open junction
Membrane resistance at 25 °C:	< 250 MΩ

Accessories Connection cables

For the SensoLyt^® armature, for the installation in a flow vessel or in a replacement fitting

• For drinking water, wastewater or in the process
• Also for high pressure and temperature conditions
• Easy to maintain by easy measuring chain replacement

Robust and impact resistant temperature measurement device for Pt 1000 penetration probe (connection Lemo size 0). TFX 420 with MIN, MAX & Hold function. For control measurements in laboratories, food sector, storage and incoming goods. For temperature determination of air, liquids, plastic substances and food. Conform to HACCP and DIN EN 13485. With battery and factory calibration certificate.

• Probes made of stainless steel, for temperatures up to +400 °C
• Accuracy: exceeds DIN IEC 584, class 1

Specifications:
Measurement range TFX 410-1 / TFX 420:	-50 ... +300 °C / -50 ... +400 °C
Accuracy:	±0.3 °C
Resolution:	0.1 °C
Sensor: Housing material: Certificate:	Pt 1000 (connection Lemo size 0) ABS 3-point factory calibration
Operating temperature: Storage temperature:	-25 °C to +50 °C -30 °C to +70 °C
Automatic switch-off:	After 2 hours, optional
Dimensions (L x W x H):	54 x 22 x 109 mm (without probe)
Weight:	Approximately 90 g
Power supply: Battery lifetime:	3.0 V Lithium, replaceable Approximately 5 years
IP code:	IP 67

Powder reagents in individually sealed packages.

Robust and precise 4 electrode graphite cells with temperatue compensation. Errors based on fringe field interference are avoided. Epoxy body.

013005MD
For use with conductivity meters Orion Star, Orion Star Plus

013010MD and 013605MD
For use with conductivity meters Star A112, Star A122, Star A212, Star A215, Star A222, Star A322, Star A325, Star A329, Versa Star, Versa Star Pro

Specifications	013005MD, 013010MD // 013605MD
Conductivity range:	1 µS/cm ... 200 mS/cm // 10 µS/cm ... 200 mS/cm
Temperature range:	-5 ... 100 °C
Diameter:	15 mm
Connection type:	8-pin Mini DIN, waterproof

Low-maintenance pH electrodes with integrated temperature sensor for temperature compensation. Recommended for media containing sulphides.

• Suitable for low-water and dirty media.
• Insensitive to anionic salts
• "i" version with integrated sensor management ISM
• With Ex-certification

Please order connection cable separately.

Specifications
pH range:	0 ... 14
Temperature range:	0 ... 130 °C
Reference system:	Solid polymer
Diaphragm:	Ceramic
Shaft diameter:	12 mm
Connection:	VarioPin